Fuji Xerox DocuPrint C5155d User Manual Download Page 106

Page: 106 / 433

106

4 Paper

Special Media

You can use the following special media such as postcards and envelopes:

Paper Name

Size

Basis Weight

(gsm)

Paper Type

Image

Quality

Notes / Countermeasure

3R98204

Unknown

Trans-parency

• Load transparencies with the edge

without the white stripe facing the
feeding slot of the tray.

• Small white dots may appear on

prints due to electric discharge of
paper.

3R96019

Unknown

Heavy-weight

L515

Unknown

Trans-parency

• Printed transparencies may stick

together when they are delivered.

• Small white dots may appear on

prints due to electric discharge of
paper.

P801

Unknown

Trans-parency

• The paper is charged with static

electricity after a print job.

• When using Tray 5, insert another

type of paper at the bottom of the
stack before loading
transparencies.

24Up

Unknown

Labels

• Print one sheet at a time, using

Tray 5.

• Do not reuse the used label or

partially peeled label.

8Up

Unknown

Labels

• Print one sheet at a time, using

Tray 5.

• Do not reuse the used label or

partially peeled label.

1Up

Unknown

Labels

• Print one sheet at a time, using

Tray 5.

• Do not reuse the used label or

partially peeled label.

Laser card

040P00142

Card 100

Extra

Heavyweight

• When using Tray 5, load the paper

with the center slightly curling
upward.

Universal

Transparency
Plain 115MIC

Unknown

Trans-parency

• If two or more sheets of

transparencies are being fed
simultaneously (double-feed), load
one sheet at a time.

V510

Unknown

Trans-parency

• Transfer deterioration might be

occurred when printing in color.
Also, toner may spatter on color
images in prints.

• When using Tray 5, insert another

type of paper at the bottom of the
stack before loading
transparencies.

16Up

Unknown

Labels

Summary of Contents for DocuPrint C5155d

















































































































































































































































































































































































































































Search results

Summary of Contents for DocuPrint C5155d

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuPrint C5155d, User Manual

Search results

Summary of Contents for DocuPrint C5155d

Reviews:

Brands by name

Popular brands