manualshive.com logo in svg

Fuji Xerox DocuPrint C5155d, User Manual

Share
Download
Fuji Xerox DocuPrint C5155d User Manual Download Page 241

6.5 Print and Image Quality Problems

241

White patches appear on output. 
Toner is scattered around 
images. 
Images are bluish. 

The image transfer voltage (the [Voltage Offset] setting on the control panel) may not be set 
properly. 
Adjust the transfer voltage on the control panel. 

Refer to

• "7.13 Adjusting the Image Transfer Voltage" (P. 368)

The paper type of the selected paper tray is not appropriate. Change the [Paper Type] 
setting and try printing again. For example, if [Paper Type] is set to [Plain], try changing it to 
[Bond] or [Recycled]. If it is set to [Heavyweight], try changing it to [Extra HW]. 

Text is smeared. 

The paper is not appropriate for the printer. Load appropriate media. 

Refer to

• " Supported Paper Type" (P. 100)

The paper is damp. Load fresh paper. 

Condensation may have formed in the printer. 
On the control panel, set the Sleep mode trigger time to more than 60 minutes and let the 
printer stand with its power on. After about an hour, the heat inside the printer causes the 
condensation to evaporate.

Refer to

• " [Sleep Mode Timer]" (P. 160)

Text is garbled. 
Printed output is not the same as 
the original data displayed on 
the computer screen. 

Is the printer set to substitute TrueType fonts with the built-in fonts? 
Change the printing method of TrueType fonts to set [Always Use TrueType Fonts] under 
[Specify Font] on the [Advanced] tab of your print driver. 

Refer to

Online help for the print driver. 

Images are skewed. 

The paper guides are not adjusted properly. Adjust the paper guides properly. 

Refer to

• "4.2 Loading Paper" (P. 110)

Color documents are printed in 
monochrome. 

Is [Black & White] selected for [Output Color] on the [Paper/Output] tab of the print driver? 
Change the [Output Color] setting to [Color]. 

Refer to

• Online help for the print driver. 

Print density or color 
reproduction has deteriorated. 

Print the Calibration Chart from the printer, compare it with the Color Sample that came with 
the printer, and perform color calibration as necessary. 

Refer to

• "7.12 Adjusting Tone Density" (P. 361)

Symptom

Cause/Remedy

Summary of Contents for DocuPrint C5155d


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands