manualshive.com logo in svg

Fuji Xerox DocuPrint C5155d, User Manual

Share
Download
Fuji Xerox DocuPrint C5155d User Manual Download Page 111

4.2 Loading Paper

111

3.

Adjust the paper guides to the size of the 
paper. 

Important

• Make sure that the guides are positioned lightly against 

the paper. Paper guides that are positioned too tight or 
two narrow can cause paper jams. 

• Do not load paper above the maximum fill-line. Doing so 

can cause paper jams.

Note

• When printing from the bypass tray, use the print driver to configure paper size and type settings. For more 

information, refer to the online help for the print driver. 

• When printing without using the print driver (such as lpr printing of a PDF file), use the printer’s control panel 

to configure the paper type setting. For more information, see "[Paper Type]" (P.179).

Bypass Tray Feed Orientations for Envelopes

When loading envelopes in the bypass tray, close the flaps of the envelopes and set them with 
the address side facing down. Configure the print driver settings depending on the types of 
envelopes and loading orientations as follows.

Note

• Register the paper size with the length of the flap included in [Custom Paper Size] when printing envelopes 

with keeping the flap open. Configure the register paper size in [Original Document Size] as well as [Output 
Paper Size], and then select [Portrait and landscape (For envelopes)] in [Image Rotation 180 Degrees].
Load the envelopes so they feed from the bottom of the envelopes (from the opposite side of the flap).

Envelope C4 (229 x 324 mm)

Monarch Envelope (3.9 x 7.5”)
No.10 Envelope(4.1 x 9.5”)
DL Envelope (110 x 220 mm)

Configure the following settings by selecting [Paper/Output] 
tab > [Paper] menu > [Advanced Paper Selection] dialog box.

• Original Document Size: Select the configured size of envelope
• Paper Tray: Tray 5 (Bypass)
• Bypass Paper Type: Envelope

Envelope C4 (229 x 324 mm)

Envelope C5 (162 x 229 mm)

Configure the following settings by selecting [Paper/Output] 
tab > [Paper] menu > [Advanced Paper Selection] dialog box.

• Original Document Size: Select the configured size of envelope
• Paper Tray: Tray 5 (Bypass)
• Bypass Paper Type: Envelope

Configure the following settings by selecting [Paper/Output] 
tab > [Paper] menu > [Mixed Sizes].

• Image Rotation 180 Degrees: Portrait and landscape (For envelopes)

Paper feed 
direction

Paper feed 
direction

Paper feed 
direction

Paper feed 
direction

Paper feed 
direction

Summary of Contents for DocuPrint C5155d


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands