FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 274

Page: 274 / 412

Page 274

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

Display Name on
Pickup/Partner Key

Display the H323-ID of the calling party instead of
the number. Usually only internal calls provide the
H323-ID (the ‘Name’ in a PBX user object)

Keep Calling Party Info on
Pickup Key

Truncate the called party info instead of the calling
party info.

Display Alerting Partners on
Pickup Key

Display alerting partners on pickup key.

Hide Display Info from ISDN
Provider

Do not display the text some ISDN Providers may
send via info indications bearing a display info
element.

Start Outbound Call on
Electronic Hook Switch (EHS)
Signal

Start outbound call on electronic hook switch (EHS)
signal.

Play Configured Ring Melody
before Automatically
Connecting an
Announcement Call

Play configured ring melody before automatically
Connecting an announcement or multicast-
announcement call.

Route Automatically
Connected Inbound Calls to
Headset (if enabled)

Route automatically connected inbound calls
(announcement, multicast-announcement) to
headset instead to speakerphone when headset is
enabled.

Connect Automatic Redialled
Call with Microphone
Switched Off

Connect automatic redialled call with microphone
switched off.

Use Headset like a Handset
Ignore Hookswitch Signals

Use headset like a handset, Ignore hookswitch
signals.

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands