FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 61 | Manualshive

Page: 61 / 412

background image

Manual ResistTel IP2 / IP152

Page 61

ExResistTel IP2 / IP154

2.4.2.4.5.6

Maintenance

When  cleaning,  ensure  that  no  moisture  is  allowed  to  penetrate  the  inside  of  the
headset.  Do  not  use  any  solvents  (e.g.  fuel,  alcohol  etc.).  Remove  any  loose  dust
with  a  soft  brush.  If  necessary,  clean  the  outside  with  a  suitable  clean  tissue  only
slightly moistened with clear water and subsequently rub the telephone dry again. If
heavily  soiled,  a  little  dishwashing  liquid  can  be  used  in  addition.  Clean  the  plug
terminals with a commonly available contact cleaning agent.

2.4.2.4.5.7

Disposal

The complete disposal of the headset will be carried out by the electronic waste. By
dismounting the components plastic, metal and electronics have to be disposed
separately. In each case the disposal conditions of the respectively country have to
be respected.

2.4.2.4.5.8

User Information

The headset is intended to be used only with the weather resistant phone
ResistTel IP2 / IP152.

After use, keep the headset at normal room temperature and at normal relative air
humidity.

The permissible operating temperature range is -10°C to +55°C; the permissible
storage temperature range is -40°C to +80°C.

Do not twist the flexible gooseneck and do not carry the headset by the gooseneck.

When operating the headset, please heed the legal and commercial / industrial
regulations, accident prevention regulations and electrical regulations / provisions.

Ensure that the connection cord does not get caught up in operational machines or
wheels.

Before repair, the headset has to be disconnected from the ResistTel IP2 / IP152.

«
...
59
60
61
62
63
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Samsung Pages: 3

Brand: Samsung Pages: 22

Brand: Samsung Pages: 115

Brand: Xiaomi Pages: 16

Brand: HTC Pages: 10

Brand: Alcatel Pages: 4

2100-TLL Landline 12v Tower

Brand: Rath Pages: 9

Brand: Avaya Pages: 11

Brand: Doogee Pages: 40

SK - 5000 ADVANCE

Brand: SK Pages: 73

Brand: Selta Pages: 54

Brand: Zte Pages: 66

Brand: Zte Pages: 25

Brand: Dukane Pages: 148

Brand: Acer Pages: 56

Brand: Acer Pages: 32

Brand: Acer Pages: 56

Brand: Acer Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands