FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 195 | Manualshive

Page: 195 / 412

background image

Manual ResistTel IP2 / IP152

Page 195

ExResistTel IP2 / IP154

Priority – Signaling

Should  your  switch  on  the  gateway  port  be  configured  on
another  VLAN  ID, you  must  input  the same  value here,  in
order  for  the  prioritising  („Priority“)  of  the  Ethernet
packages  to  work.  Here,  the  priority  of  the  VLAN  ID  for
signalling  data  is  given  in  values  from  zero  to  seven.  By
default the priority for signalling is the same as the priority
for voice data.

4.4.3

Menu 802.1X

EAP-MD5:

User

User

Password

Password

The State will be displayed also.

4.4.4

Menu Statistics

Via the submenu Statistics you get an overview of all sent (tx) and received (rx) data
packages regarding the LAN Link, PC link and CPU Link interface:

tx-good

The number of successfully sent packages.

tx-unicast

The number of successfully sent Unicast packages.

tx-broadcast

The number of successfully sent Broadcast packages.

tx-multicast

The number of successfully sent Multicast packages.

tx-deferred

The number of deferred packages.

«
...
193
194
195
196
197
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Aastra Pages: 19

Clearspan 6757i

Brand: Aastra Pages: 2

Brand: Aastra Pages: 36

Brand: Aastra Pages: 56

Brand: Aastra Pages: 80

Brand: palmOne Pages: 2

Brand: Uriver Pages: 109

UNIVERGE SV8100 DT7 SERIES

Brand: NEC Pages: 16

Brand: Jacob Jensen Pages: 76

Brand: Manta Pages: 20

Brand: TCL Pages: 20

Brand: TCL Pages: 10

Brand: Alcatel Pages: 58

Brand: M4 Pages: 22

Brand: Zte Pages: 46

Brand: GENERAL MOBILE Pages: 107

Brand: Siemens Pages: 38

GIGASET EUROSET 2015

Brand: Siemens Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands