FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 262 | Manualshive

Page: 262 / 412

background image

Page 262

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

Local Coder

The protocols for the speech compression in the local network
are listed in this parameter. The desired local coder can be
selected: One of the following coder can be selected:

•

G711A (ISDN Europe)

•

G711u (ISDN North of America, Japan)

•

G729A

Framesize [ms]

For Local Coder:

The package sizes are automatically negotiated with 30 ms.
This parameter enables the determination of another RTP
package size.

Silence
compression

For Local Coder:

Taking the VoIP telephone as the starting point, in case of
silence (no conversation), no packages are sent. On the other
side, noise is played back.

«
...
260
261
262
263
264
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Sangoma Pages: 12

Dialog 4422 IP Office

Brand: Aastra Pages: 151

Brand: Aastra Pages: 2

Dialog 4420 IP Basic

Brand: Aastra Pages: 74

Brand: Aastra Pages: 101

Clearspan 6739i

Brand: Aastra Pages: 9

Clearspan 6739i

Brand: Aastra Pages: 8

Clearspan 6739i

Brand: Aastra Pages: 20

Brand: Aastra Pages: 104

Brand: Aastra Pages: 108

Clearspan 6731i

Brand: Aastra Pages: 2

Brand: Aastra Pages: 7

Brand: Aastra Pages: 1140

Brand: Aastra Pages: 174

Brand: Aastra Pages: 888

Dialog 5446 IP Premium

Brand: Aastra Pages: 87

Brand: Lancom Pages: 50

Alltel Hue II SCH-R600 Series

Brand: Samsung Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands