FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 96 | Manualshive

Page: 96 / 412

background image

Page 96

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

3.3.15

Send Message

If no-one answers your call, or you hear the busy tone, you may send a message.

1.

Press the key if the busy tone or the distant dial tone can be heard. Using the
cursor keys, select the item Send Message and press the key .

Peter

Recall
Redial
Intrude

Send Message

< Recall

Figure 49: Send Message

For:72

<< Message

a

Figure 50: Message

2.

The message can be entered with the keypad alphanumerical. The message will
be sent by pressing the key . The sending of the message can be aborted by
pressing the key .

3.3.16

Management of the Waiting List

Your VoIP telephones are perfectly suited to be used as a small exchange. You are
able to hold more than two calls at a time. The number of maximum serviceable calls
can be freely configured. Contact your PBX administrator to find out more about your
settings.

The waiting list can be operated in two operating modes.

3.3.16.1

Operating Mode 1

To access this operating mode, press the key.

In this operating mode two calls from your waiting list are displayed.

«
...
94
95
96
97
98
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: NEC Pages: 2

Yealink SIP-T46G

Brand: Yealink Pages: 8

Brand: Samsung Pages: 337

Brand: Samsung Pages: 158

Brand: ASCOM Pages: 46

Brand: iBall Pages: 17

Brand: Denver Pages: 168

Brand: Alcatel Pages: 73

Brand: HTC Pages: 2

Brand: Yezz Pages: 80

Brand: Teldat Pages: 165

Alcatel VFD 900

Brand: TCL Pages: 74

Brand: Nortel Pages: 112

Brand: Mobistel Pages: 24

Brand: Polycom Pages: 2

R520_CJ16_MM_111009_F4

Brand: Samsung Pages: 169

Renown SCH-U810

Brand: Samsung Pages: 169

Brand: Samsung Pages: 222

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands