manualshive.com logo in svg

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Download the comprehensive Operating Instructions Manual for FHF ExResistTel IP2/IP154, a cutting-edge communication device. This manual provides step-by-step guidelines for optimal usage and troubleshooting, ensuring a seamless experience. Get your free download of this essential manual at manualshive.com, empowering you to make the most of your product.

Share
Download
background image

 

Page 366 

Manual  

ResistTel IP2 / IP152 

 

  ExResistTel IP2 / IP154 

 

4.11.24

 

SIP / TSIP / SIPS Protocol Option 'No HR Notify' 

With  the  SIP  /  TSIP  /  SIPS  protocol  option  'No  HR  Notify'  the  Hold  Notify  and  the 
Retrieve Notify signalling will be suppressed. 

Append to the configuration line "config change <prot>" the option "/no-hr-notify". 

With <prot> = SIP, TSIP or SIPS. 

4.11.25

 

SIP / TSIP / SIPS Protocol Option 'Prefer Tel URI' 

With the SIP / TSIP / SIPS protocol option Prefer Tel Uri  the use of telephone URI’s 
in stead of SIP URI’s will be preferred. 

Append to the configuration line "config change <prot>" the option "/prefer-tel-uri". 

With <prot> = SIP, TSIP or SIPS. 

4.11.26

 

SIP / TSIP / SIPS Protocol Option 'Prefer 'PAI' 

With the SIP / TSIP / SIPS protocol option 'Prefer PAI' the use of PAI’s (P-Asserted 
Identity) will be preferred. 

Append to the configuration line "config change <prot>" the option "/prefer-pai". 

With <prot> = SIP, TSIP or SIPS. 

4.11.27

 

SIP / TSIP / SIPS Protocol Option 'Prefer PAI2' 

With the SIP / TSIP / SIPS protocol option 'Prefer PAI2' the use of the second PAI (P-
Asserted Identity) will be preferred.  

Append to the configuration line "config change <prot>" the option "/prefer-pai2". 

Mit <prot> = SIP, TSIP or SIPS. 

4.11.28

 

SIP / TSIP / SIPS Protocol Option 'Force PAI' 

With the SIP / TSIP / SIPS protocol option 'Force PAI' the use of PAI’s (P-Asserted 
Identity) will be forced. 

Append to the configuration line "config change <prot>" the option "/pai". 

With <prot> = SIP, TSIP or SIPS. 

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

3Com VCX V7000 Manager'S Manual preview
VCX V7000
Brand: 3Com Pages: 118
3Com CoreBuilder 3500 Manual preview
CoreBuilder 3500
Brand: 3Com Pages: 92
T-Mobile Sidekick 3 Start Manual preview
Sidekick 3
Brand: T-Mobile Pages: 4
i.safe MOBILE IS330.1 Quick Start Manual preview
IS330.1
Brand: i.safe MOBILE Pages: 21
RADVision Scopia XT5000 Series Installation Manual preview
Scopia XT5000 Series
Brand: RADVision Pages: 184
Samsung SM-C105A User Manual preview
SM-C105A
Brand: Samsung Pages: 283
AGM 2A3DR-H5 Manual preview
2A3DR-H5
Brand: AGM Pages: 11
Sony Ericsson T102 User Manual preview
T102
Brand: Sony Ericsson Pages: 74
M4 SS990 Quick Start Manual preview
SS990
Brand: M4 Pages: 22
AU Infobar C01 Basic Manual preview
Infobar C01
Brand: AU Pages: 96
Talk To Me Technologies Wego Write Quick Reference preview
Wego Write
Brand: Talk To Me Technologies Pages: 2
Blaupunkt BS 06 User Manual preview
BS 06
Brand: Blaupunkt Pages: 30
Samsung SM-N920S User Manual preview
SM-N920S
Brand: Samsung Pages: 153
BRONDI AMICO SMART Instruction Manual preview
AMICO SMART
Brand: BRONDI Pages: 15
Lenovo Moto G5 Plus Read Me preview
Moto G5 Plus
Brand: Lenovo Pages: 92
Lenovo Moto G8 Service And Repair Manual preview
Moto G8
Brand: Lenovo Pages: 103
Lenovo Moto G5S Read Me preview
Moto G5S
Brand: Lenovo Pages: 88
Lenovo Moto G8 Plus Service And Repair Manual preview
Moto G8 Plus
Brand: Lenovo Pages: 121

Brands by name

Popular brands

Load more brands