FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 226 | Manualshive

Page: 226 / 412

background image

Page 226

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

4.7.1.1

Submenu General

Here the parameters are input for logging into the PBX. These parameters are preset
by the administrator of the telephone system.

Enable

Here the registration (user) will be enabled. Registration
1 is always enabled.

First, the required protocol must be chosen for registration. You have the choice
between the protocols H323, SIP, TSIP and. SIPS. The corresponding parameters are
automatically adapted to the selected protocol.

Protocol H323:

Primary Gatekeeper
Address

Here, the IP address is input, under which the first
responsible gatekeeper can be reached.

Secondary Gatekeeper
Address

If the first gatekeeper cannot be reached, for security
purposes there should be another gatekeeper in the
network. The IP address of this gatekeeper should be
entered here.

Note

If no gatekeeper address is defined and the protocol is set to H.323, then the
telephone will search for a gatekeeper via the gatekeeper recovery.



Gatekeeper Identifier

If several gatekeepers are to be active on one address,
among these a certain gatekeeper is identified on the
basis of the name that is to be entered here.

Number

Telephone numbers that are required for the
registration are entered here.

«
...
224
225
226
227
228
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Univerge SV8100

Brand: NEC Pages: 4

Brand: Panasonic Pages: 4

Brand: QMobile Pages: 66

Brand: NEC Pages: 216

Brand: Talkswitch Pages: 29

Brand: Talkswitch Pages: 3

Yealink SIP-T22P

Brand: Yealink Pages: 4

Yealink SIP-T22P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 12

Brand: Yealink Pages: 8

Yealink SIP-T21P

Brand: Yealink Pages: 144

Yealink SIP-T41P

Brand: Yealink Pages: 178

Brand: NEC Pages: 61

Brand: T-Mobile Pages: 211

wego A-PLUS Series

Brand: Talk To Me Technologies Pages: 28

Brand: BenQ Pages: 97

Brand: Majestic Pages: 57

Brand: Yealink Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands