FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 119 | Manualshive

Page: 119 / 412

background image

Manual ResistTel IP2 / IP152

Page 119

ExResistTel IP2 / IP154

6.

In order to store the selection, leave the menu by pressing the key three
times.

The set Call waiting variety has now been activated.

The Number Presentation allows you to enable or disable the display of your own
telephone number when making a call.

Setting the Number Presentation:

1.

While the telephone is in its initial condition, press the key or .

2.

Use the cursor keys to select the

User Setup

menu.

3.

Press the key . The screen in Figure 85 appears.

4.

Use the cursor keys to select the

Number Present.

menu.

5.

If you press the key at this point, you can switch between „On“ and „Off“.

6.

In order to store the selection, leave the menu by pressing the key three
times.

The current setting is valid for all subsequent calls, unless the setting is enabled or
disabled specifically for an individual call.

A deactivated Number Presentation is displayed in the status bar by the symbol .

3.8.1

Call Diversion

The

call diversion

menu allows you to be available even if you are not in the office.

Note

The call diversion is working according to the standard H.450. The gatekeeper must
support this protocol.

Otherwise the option local call forward can be activated (see chapter 4.11.9
Protocol Option 'Local Call Forward on page 360).

If the gatekeeper doesn’t support this protocol (The telephone is set to the protocol
SIP/TSIP/SIPS.) and the local call diversion is not activated, the item “call
diversion” doesn’t appear in the menu of the VOIP telephone.



«
...
117
118
119
120
121
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Nec Casio Pages: 390

Brand: Unitech Pages: 2

TracFone SGH-T155G Series

Brand: Samsung Pages: 56

TracFone SGH-T245G

Brand: Samsung Pages: 88

Trender SPH-M380

Brand: Samsung Pages: 192

Brand: HTC Pages: 80

Brand: 4blind Pages: 28

Brand: Profoon Pages: 56

Brand: Sony Ericsson Pages: 64

Brand: Samsung Pages: 133

Brand: Alcatel Pages: 40

Brand: Acer Pages: 32

Liquid Mini E310

Brand: Acer Pages: 63

CloudMobile S500

Brand: Acer Pages: 66

Brand: Acer Pages: 58

Brand: Acer Pages: 76

Brand: Acer Pages: 96

Brand: Acer Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands