FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 334 | Manualshive

Page: 334 / 412

background image

Page 334

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

Code

Name

Description

0x00090002 CF Card: Error

The next cluster of a file or a directory is out
of range. This error should not occur. Be
sure to run chkdsk.

0x00090003 CF Card: Error

The underlying driver returned no data. This
can be caused by an invalid cluster or if the
card was removed while operations are
performed on it. Be sure to run chkdsk.

0x00090004 CF Card: Error

The card is full. You can buy a bigger one or
delete some unnecessary files.

0x00090005 CF Card: Error

The card is unformatted or formatted with
an unknown format. Be sure to format it
with fat32.

0x00090006 CF Card: Error

The card has a wrong disk format. The
needed format is fat32. Be sure to format it.

0x000a0000 ISDN Interface

Faults of the group ISDN Interface

0x000a0001 ISDN Interface: Error

Signalling error reported by ISDN interfaces:
A broadcast packet was received on a point-
to-point interface, which should not happen.
This indicates that there is a configuration
mismatch point-to-point/point-to-multipoint.

0x000b0000 CMD

Faults of the group CMD

«
...
332
333
334
335
336
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Xblue Networks Pages: 106

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Yealink SIP-T28P

Brand: Yealink Pages: 10

Yealink SIP-T28P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 4

Yealink SIP-T28P

Brand: Yealink Pages: 2

Yealink SIP-T28P

Brand: Yealink Pages: 4

Brand: Yealink Pages: 158

Brand: Yealink Pages: 6

Brand: Yealink Pages: 4

Brand: Yealink Pages: 16

Brand: Yealink Pages: 73

Brand: Yealink Pages: 120

Brand: Yealink Pages: 2

Brand: Krüger & Matz Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands