FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 91

Page: 91 / 412

Manual ResistTel IP2 / IP152

Page 91

ExResistTel IP2 / IP154

Put the handset back on its rest (handset mode).

Press the loudspeaker key (hands free mode).

Press the headset key (Key long (longer than a second) and then the
loudspeaker key ) (headset mode).

Press the key

(short) followed by the key

. The caller will be

connected with the dialled number.

Tip

When transferring a call, you do not have to wait until the desired subscriber
answers. You can hang up immediately after dialling the phone number.

3.3.10

Transferring a Call directly

You are making a call and want to switch it to another connection.

Torsten                     72
Peter                       36

  Transfer

Figure 44: Transferring a Call Directly

Press the key (long) during a call.

You will be left. The actual connection will not be displayed.

Dial the call number of your choice.

Press the key (short) or key .

The caller will be connected with the dialled port directly.

With handset mode hang up.

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands