FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 21

Page: 21 / 412

Manual ResistTel IP2 / IP152

Page 21

ExResistTel IP2 / IP154

Position

Symbol

Description

Name (H.323 or SIP ID or nickname of the PBX
configuration)

Status line; provides information on the current status of the
telephone by means of the following symbols.

06.04.10

Date

14:00

Time

No connection to the Ethernet (primary Ethernet port)

Connection established to the gatekeeper

Connection established to the secondary gatekeeper

Connection to the gatekeeper broken. (Both symbols are
displayed in mutual change.)

Open listening

Hands free Mode

Microphone switched off (symbol flashing)

Call diversion activated

Handset activate

Headset active

Telephone locked

Calling number transmission locked

Own call number (E.164)

Called party

Calling party

Unknown number/name, unresolved number

Diverting party

Transferring party

Returning call

Call pending

Call on hold

Shift Mode

Headset configured

Audio connection of the active call is encrypted (SRTP)

0:12

Duration of the active call

Table 2: Contents of the Default Display

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands