FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 409

Page: 409 / 412

Manual ResistTel IP2 / IP152

Page 409

ExResistTel IP2 / IP154

Environmental conditions

Ambient operating temperature

-40°C…+70°C

Transport and storage temperature

-40°C…+80°C

Conformities

Degree of protection

IP66 acc. to EN/IEC 60529

Degree of protection against external
mechanical impacts

IK09 acc. to EN/IEC 62262

Declaration of Conformity

Directive 1999/5/EU (R&TTE)
Directive 2004/108/EG (EMC)
Directive 2006/95/EG (low voltage)

Restriction of Hazardous Substances
(ROHS)

Directive 2011/65/EG

Waste Electrical and Electronic
Equipment (WEEE)

Directive 2012/19/EG
EAR registration no.: DE 58023377

User interface

Web-interface (administration)

English

Telephone (user menu)

16 languages adjustable

9.2

Explosion Proof Telephones

Connection data

Power supply

Power over Ethernet refer to IEEE
802.3af or external power supply

Voltage PoE

48V DC (Min. 44V, Max. 57V). The power
has to be transmitted at 10/100 Mbit/s
Ethernet connections only with the
unused pairs of data lines.

PoE

Class 0

Voltage external power supply

19.2 V – 52.8 V DC

Power requirement

12.95 W

Switching power relays

250 V, 5 A, 100 VA AC
230 V, 0.5 A, 100 W DC
50 V, 1 A, DC
30 V, 5 A, 100 W DC

Connection Ethernet

Terminals (10/100 Mbit/s)

Ringing volume

Max. 95 dB(A) in 1 m distance

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands