FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 36 | Manualshive

Page: 36 / 412

background image

Page 36

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

•

The speech speed hopper of the handset consists out of a not electrical

conductive plastic material. It may be charging with high air speed
dangerously. A cleaning of the speech speed hopper with pressed air is not
allowed.

•

Changes of the product for technical improvement are possible without

announcement before.

•

The configuration conductor will be used for configuration by the

manufacturer exclusively and must not be connected. Programming by the
installer is not allowed.

•

The  telephone  has  to  be  included  into  the  potential  equalisation  either  with
the internal earth connecting bolt of the metal plate or with the external earth
connecting  bolt  at  the  housing  (see  examples  of  connection).  The  potential
equalisation  must  exist  inside  and  outside  of  the  explosion  at  risk  area.  The
potential equalisation is necessary to support the explosion protection.

Caution

The equipment is suitable for use in Group II, Category 2G and 2D or non-
hazardous locations only.

WARNING – EXPLOSION HAZARD

Do not disconnect equipment unless power has been removed or the area is known
to be non-hazardous.

WARNING – EXPLOSION HAZARD

Substitution of any components may impair suitability for Group II, Category 2G and
2D.

•

The telephone may be operated solely under the stated ambient conditions.
Unfavourable ambient conditions can lead to damage of the telephone and
thus present a potential danger for the user.

«
...
34
35
36
37
38
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 112

Yealink SIP-T22P

Brand: Yealink Pages: 4

Yealink SIP-T22P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 12

Brand: Yealink Pages: 8

Yealink SIP-T21P

Brand: Yealink Pages: 144

Yealink SIP-T41P

Brand: Yealink Pages: 178

Brand: UMX Pages: 12

Brand: Amron Pages: 28

Brand: Yealink Pages: 19

Brand: Pantech Pages: 261

Brand: UMI Pages: 44

Brand: EMPORIA Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands