FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 201

Page: 201 / 412

Manual ResistTel IP2 / IP152

Page 201

ExResistTel IP2 / IP154

Mode server:

Probe Address before dynamic
Assignment

•

disabled

•

ARP

•

PING

Reserved and same Vendor Clients only

Use of specific leases only.

Server Identifier

Value of manufacturer specific option
250 sent by the server and expected by
the client (can be left empty)

When the telephone is working in DHCP client mode the parameters of the current
lease are displayed.

Item

Description

Current Lease from

IP address of the DHCP server

IP Address

IP address of the telephone

Network Mask

Network mask of the telephone

Default Gateway

IP address of the default gateway

TOS Priority

Type of service priority

IP Routing

IP routing

DNS Server 1

IP address of the domain name server 1

DNS Server 2

IP address of the domain name server 2

Domain Name

SYSLOG Server

IP address of the SYSLOG server

TFTP Server

IP address of the trivial file transfer protocol server

Time Server 1

IP address of the first time server

Time Server 2

IP address of the second time server

Timezone String

Timezone string

WINS Server

IP address of the Windows Internet Naming Service
server

Node Type

Primary Gatekeeper

IP address of the primary gatekeeper

Secondary Gatekeeper

IP address of the secondary gatekeeper

Coder

Name of the coder

Gatekeeper Identifier

Gatekeeper identifier

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands