FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 170

Page: 170 / 412

Page 170

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

•

europe-pbx

•

europe-public

•

italy-pbx

•

italy-public

•

czech-pbx

•

czech-public

•

sweden

•

france

•

swiss

•

belgium

•

netherlands

•

norway

•

denmark

•

germany

•

spain

•

finland

•

austria

•

ireland

•

australia

•

newzealand

•

malaysia

•

turkey

•

russia

•

south africa

•

brazil

Tones: europe-pbx

Options

Figure 187: Menu Options

3.11.4

Reset Configuration

The

reset configuration

menu offers the possibility of restoring the default settings

for the device. All settings made in the meantime will be lost in the process.

In the initial condition press the key or .

Use the arrow keys to select the menu

Administration

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands