FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 146 | Manualshive

Page: 146 / 412

background image

Page 146

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

Type: Call Forwarding

State: 4
Text:
Icon:
LED: Off

Function Keys

Figure 133: Function Keys (Type Call Forwarding, State 4)

This  function  allows  incoming  calls  to  be  diverted.  Four  states  with  different
destinations  can  be  configured  (for  example,  mobile  phone,  voicemail),  which  are
offered in succession. In each of these states, the following options can be used:

Always

This indicates a permanent call diversion.

Busy

The call diversion is activated if one’s own telephone is busy.

No Response

The call diversion is activated after a delay, e.g. four rings.

3.10.5.9

Function Key Call Group

Type: Call Group

State: 1
Text:
Icon:
Name:

Function Keys

Figure 134: Function Keys (Type Call Group, State 1)

Type: Call Group

State: 2
Text:
Icon:
LED:
Name:

Function Keys

Figure 135: Function Keys (Type Call Group, State 2)

«
...
144
145
146
147
148
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: TCL Pages: 52

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 112

OpenStage M3 Plus

Brand: Unify Pages: 89

Brand: Planet Pages: 2

Brand: Caliber Pages: 10

Brand: Allview Pages: 108

Brand: Polycom Pages: 2

Yealink SIP-T27

Brand: Vox Pages: 12

ON-AIR 2000 EXECUTIVE

Brand: BT Pages: 25

Brand: Sony Ericsson Pages: 26

Brand: Samsung Pages: 95

Brand: Samsung Pages: 92

Brand: Samsung Pages: 132

Brand: Samsung Pages: 38

Brand: Samsung Pages: 157

Brand: Samsung Pages: 149

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands