FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 345 | Manualshive

Page: 345 / 412

background image

Manual ResistTel IP2 / IP152

Page 345

ExResistTel IP2 / IP154

Code

Name

Description

0x00110052 Network: UDP

checksum

UDP checksum

0x00110053 Network: UDP bind

error

Local error.

UDP socket was trying to bind itself to a
specific local port number.

The port number was found to be in use by
some other socket.

0x0011005a Network Route Error:

no route

No route

0x0011005b Network Route Error:

No route through
interface (Interface
down)

The IP routing process failed to deliver a
packet explicitly directed to a specific
network interface. The network interface
was either down or disabled. Packets
directed to a specific network interface are
used for example by DHCP (UDP) and by
PPTP Tunnels (TCP/GRE).

If this error is reported for UDP broadcast
packets rather often it usually indicates that
DHCP client mode is configured for the
interface but the interface is not connected
to a network or disabled. In this case the
DHCP mode should be changed to disabled.

0x0011005c Network Route Error:

Interface unconfigured

Interface not configured

0x0011005d Network Route Error:

Interface no gateway

Interface is no gateway

«
...
343
344
345
346
347
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Yealink Pages: 229

Brand: Samsung Pages: 22

Brand: Samsung Pages: 50

Brand: Samsung Pages: 37

Brand: Samsung Pages: 95

Brand: Samsung Pages: 131

Brand: Samsung Pages: 153

Brand: Samsung Pages: 155

Brand: Samsung Pages: 189

R225 - SGH Cell Phone

Brand: Samsung Pages: 65

Brand: Samsung Pages: 118

Brand: Samsung Pages: 38

Brand: mPTech Pages: 50

Brand: Docomo Pages: 228

Brand: UMI Pages: 44

Brand: EMPORIA Pages: 24

Brand: TCL Pages: 33

Brand: Pantech Wireless Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands