FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 206 | Manualshive

Page: 206 / 412

background image

Page 206

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

It can be entered more than one address area.

Offer Parameters:

Network Mask

The corresponding network mask regarding the IP address

Default Gateway

The standard-router (e.g.: 192.168.1.1).

TOS Priority

The Type-Of-Service (TOS) value for voice packages.

IP Routing

There is the possibility to add statistic IP routes. These
must be input in the form of Address:Mask:Gateway. The
elements must be separated from each other by a colon. By
ending a route with a ‚;’, more routes can be added.

DNS Server 1

The primary DNS server address

DNS Server 2

The secondary DNS server address

Domain Name

Domain name that client should use when resolving
hostnames via DMS (aka primary DNS prefix)

SYSLOG Server

The SYSLOG server address

TFTP Server

The TFTP server address (based on FTP)

Time Server 1

The first time server address

Time Server 2

The second time server address

«
...
204
205
206
207
208
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: T-Mobile Pages: 4

Brand: Olympia Pages: 54

Brand: Hanlong Pages: 57

Brand: 2N Pages: 32

9520 - Charging Pod For

Brand: Blackberry Pages: 2

8700 - 8707H SMARTPHONE

Brand: Blackberry Pages: 48

Brand: Sagem Pages: 70

Brand: jablotron Pages: 7

Brand: SoftBank Pages: 36

Brand: Alcatel Pages: 2

AQUOS ZETA SH-09D

Brand: Docomo Pages: 45

Brand: Nodis Pages: 20

Brand: fine line Pages: 6

Brand: TCL Pages: 33

Brand: Sagem Pages: 84

Brand: Bosch Pages: 2

Brand: Polycom Pages: 12

Brand: Zte Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands