FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 112

Page: 112 / 412

Page 112

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

With the arrow keys, select the input field

Number

and correct the entry, if

required.

With the arrow keys, select the input field

Name

and correct the entry, if

required. This Entry is used for dialling.

In order to save your changes, press the key

The entry saved message appears and the alphabetical telephone directory list is re-
opened.

In order to delete an entry, use the arrow keys to select the menu

Delete

and

press the key .

You are asked whether the entry is to be deleted.

In order to confirm the deletion, use the arrow keys to select the entry

Yes

and

press

The entry deleted message appears and the alphabetical telephone directory list is
re-opened.

In order to abort the deletion, use the arrow keys to select the entry

and

press .

You are returned to the subscriber data.

3.6.4.1

Setup

Proceed as follows to adjust the settings:

In the Directory Input, use the cursor keys to select the

Setup

menu.

Press the key . The following will be display:

Ringing On

Ringing Tone..................
Registration..................

Setup

Figure 73: Menu Setup

Set the ringing tone

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands