FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 225 | Manualshive

Page: 225 / 412

background image

Manual ResistTel IP2 / IP152

Page 225

ExResistTel IP2 / IP154

After entering a route it is necessary to click at the OK button to take over the data.
The data will be taken over and the window will be closed. Wit the next call of the
same interface, there will be the possibility to enter an additional IPv6 route.

4.6.3.2

Submenu State

A table with the main parameters and states of the IPv6ToIPv4 interfaces will be
displayed.

For each interface the following parameter will be displayed:

Interface

•

6TO4-00

•

6TO4-01

Name

Name of the interface

Destination

IPv4 destination address

Source

IPv4 source address

State

•

Down

•

Up

Route

All IPv6 destination addresses

4.7

Main Menu Phone

4.7.1

Menus User-1 to User-6

The telephone has been designed for multiple registrations. Up to six different
registrations can be stored in one VoIP telephone. Each registration must be
configured in a separate item of the main menu. (User-1 to User-6)

«
...
223
224
225
226
227
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: Eads Telecom Pages: 2

Brand: Pantech Pages: 182

Brand: Pantech Pages: 88

Brand: Pantech Pages: 4

Pantech Perception

Brand: Pantech Pages: 202

Brand: Pantech Pages: 3

Brand: Pantech Pages: 120

DEL USUARIO PG-1610

Brand: Pantech Pages: 79

Brand: Pantech Pages: 169

Brand: Pantech Pages: 42

Brand: JabloCom Pages: 16

Brand: Sagem Pages: 115

Brand: cromax Pages: 9

Brand: Sony Ericsson Pages: 114

Brand: Verykool Pages: 58

Brand: OUKITEL Pages: 60

Brand: Ice Mobile Pages: 10

Brand: Zte Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands