FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 281 | Manualshive

Page: 281 / 412

background image

Manual ResistTel IP2 / IP152

Page 281

ExResistTel IP2 / IP154

Number

Calling number of the user

Name

Name of the registration

Gatekeeper
Address

IP address of the gatekeeper that received the registration.

Gatekeeper
Identifier

ID of the gatekeeper that accepted the registration.

Gatekeeper
Instance

•

primary:

The registration will be carried out at the

primary gatekeeper.

•

secondary:

The registration will be carried out at the

secondary gatekeeper

Protocol

VoIP Protocol H.323, SIP, TSIP or SIPS

Active

Shows which user is actively registered on the VoIP telephone.

If more than one registration is registered successfully, then another registration can
be selected as the active registration. With clicking the OK button the active
registration can be switched over.

4.7.6.2

Submenu Calls

In this submenu all active connections of the phone will be displayed.

In the table the following parameter will be displayed.

«
...
279
280
281
282
283
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Brand: ZEN Pages: 62

Brand: Iget Pages: 54

Brand: Damall Pages: 7

OpenStage SL4 professional HiPath Cordless...

Brand: Unify Pages: 80

Brand: Blu Pages: 20

Brand: Alcatel Pages: 56

Brand: Planet Pages: 8

Xperia Play R800A

Brand: Sony Ericsson Pages: 19

Brand: UMI Pages: 44

Brand: EMPORIA Pages: 24

Vogue 2.8a SLEEC

Brand: iBall Pages: 23

Brand: Intelbras Pages: 52

Brand: Samsung Pages: 119

Brand: Samsung Pages: 125

Brand: Samsung Pages: 104

Brand: Panasonic Pages: 14

Brand: Lenovo Pages: 92

Brand: Lenovo Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands