FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 198 | Manualshive

Page: 198 / 412

background image

Page 198

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

4.5.1

Menu General

4.5.1.1

Submenu Settings

The TOS (Type of Service) byte inside the IP header is used for prioritization of
packets inside the network. The device allows some packets to be marked as higher
priority. The TOS values for this purpose are configured here.

TOS priority – RTP
Data

If  your  router  is  able  to  set  priorities  on  the  basis  of  the
„type of service“ (TOS) field, this function can be used for
speech  packets.  By  this  speech  data  will  be  served  with
priority. The value to be entered here must be aligned with
the  value  of  the  network  router.  The  value  of  0xb8  is
default.

TOS priority –
Signalling

If your router is able to set priorities on the basis of the
„type of service“ (TOS) field, this function can be used for
signalling packets. By this signalling data will be served
with priority. The value to be entered here must be aligned
with the value of the network router. The value of 0x68 is
default.

Note

You may enter the values hexadecimal, octal or decimal. The entries 0x10, 020 and
16 are equivalent. Please note, however, that the value for the TOS field should be
identically set on all devices.



«
...
196
197
198
199
200
...
»

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExResistTel IP2/IP154

Redmi Note 10 JE

Brand: Xiaomi Pages: 10

8110 - Pearl - AT&T

Brand: Blackberry Pages: 54

ONETOUCH POP 7S P330X

Brand: Alcatel Pages: 32

Brand: Alcatel Pages: 51

Blackview GBV7100

Brand: Iget Pages: 62

Brand: Archos Pages: 14

Brand: M4 Pages: 22

Brand: Pantech Pages: 97

Brand: M4TEL Pages: 13

Brand: OUKITEL Pages: 39

Brand: Samsung Pages: 184

Brand: Samsung Pages: 184

Brand: Xiaomi Pages: 8

Brand: IPRO Pages: 53

Brand: Wherify Pages: 37

Brand: Verizon Pages: 46

Brand: Innovall Groups Pages: 40

Brand: GENERAL MOBILE Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands