FHF ExResistTel IP2/IP154 Operating Instructions Manual Download Page 344

Page: 344 / 412

Page 344

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

Code

Name

Description

0x0011001f Network: RT3

misconfigured

RT3 configured not correctly

0x00110040 Network: IP checksum

error

IP checksum error

0x00110041 Network: ARP

poisoning

ARP poisoning

0x00110046 Network: TCP NAT

ports exhausted

TCP NAT ports exhausted

0x00110047 Network: TCP ports

exhausted

TCP ports exhausted

0x00110048 Network: TCP

checksum

TCP checksum

0x00110049 Network: TCP bind

error

Local error.

TCP socket was trying to bind itself to a
specific local port number.

The port number was found to be in use by
some other socket.

0x00110050 Network: UDP RTP

ports exhausted

UDP RTP ports exhausted

0x00110051 Network: UDP ports

exhausted

UDP ports exhausted

Summary of Contents for ExResistTel IP2/IP154





























































































































































































































































































































































































































Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands

FHF ExResistTel IP2/IP154, Operating Instructions Manual

Search results

Summary of Contents for ExResistTel IP2/IP154

Reviews:

Related manuals for ExResistTel IP2/IP154

Brands by name

Popular brands