manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Service Manual

The Covidien Puritan Bennett 700 Series service manual is essential for maintaining and troubleshooting your medical equipment. Download the manual for free from manualshive.com to ensure optimal performance and reliable operation of your device. Get the detailed instructions you need to properly service your Puritan Bennett 700 Series product.

Share
Download
background image

S

ECTION

Puritan Bennett™ 700 Series Ventilator System Service Manual

10070389 Rev. A

xi

Table of Contents

2

1

General information

1.1

How to use this manual............................................................................................. 1-1

1.2

Safety .......................................................................................................................... 1-1

1.3

General description.................................................................................................... 1-2

1.4

Configuration information........................................................................................ 1-4

1.5

Accessories.................................................................................................................. 1-4

1.6

Specifications.............................................................................................................. 1-4

1.7

Manufacturer’s Declaration ...................................................................................... 1-9

1.8

Tools, equipment, and service materials ................................................................ 1-15

1.9

Periodic maintenance .............................................................................................. 1-18

1.10 Service kits ................................................................................................................ 1-19
1.11 Controls and indicators............................................................................................ 1-19

1.11.1 Ventilator Settings ...................................................................................... 1-22
1.11.2 Patient Data  ............................................................................................... 1-27
1.11.3 Ventilator Status  ........................................................................................ 1-30

1.12 Location of ventilator serial number ...................................................................... 1-31
1.13 Determining software revision ............................................................................... 1-31
1.14 Service philosophy ................................................................................................... 1-31
1.15 Reference documentation....................................................................................... 1-32

2

Theory of operation

2.1

Overview of ventilator operation ............................................................................. 2-1

2.2

Pneumatic system....................................................................................................... 2-3
2.2.1

Gas Inlet System Overview ........................................................................... 2-7

2.2.1.1

Gas inlet system components................................................................ 2-10

2.2.1.2

System operation ................................................................................... 2-12

2.2.2

Piston/cylinder system................................................................................. 2-14

2.2.2.1

Component descriptions ....................................................................... 2-14

2.2.2.2

Operational description of piston/cylinder system .............................. 2-16

2.2.3

Inspiration manifold system ....................................................................... 2-21

2.2.3.1

Component descriptions ....................................................................... 2-21

2.2.3.2

Operational description ........................................................................ 2-22

2.2.4

Patient system ............................................................................................. 2-25

2.2.5

Exhalation system ....................................................................................... 2-28

2.2.5.1

Component descriptions ....................................................................... 2-28

2.2.5.2

Operational description ........................................................................ 2-31

2.2.6

PEEP/CPAP system ....................................................................................... 2-32

2.2.6.1

Component descriptions ....................................................................... 2-32

2.2.6.2

System operation ................................................................................... 2-32

2.3

Electrical system  ...................................................................................................... 2-35
2.3.1

Power assembly........................................................................................... 2-39

2.3.1.1

Power input section............................................................................... 2-41

2.3.1.2

Power supply.......................................................................................... 2-43

2.3.1.3

Battery backup (BBU) PCB ..................................................................... 2-43

2.3.1.4

Power supply fan ................................................................................... 2-45

2.3.2

Internal battery ........................................................................................... 2-46

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Puritan Bennett 700 Series

ABB SACE Tmax XT Series Manual preview
SACE Tmax XT Series
Brand: ABB Pages: 11
GE RGB1-G60-8 Use And Care Instructions preview
RGB1-G60-8
Brand: GE Pages: 2
GE Druck DPI 620 Genii Quick Start Manual preview
Druck DPI 620 Genii
Brand: GE Pages: 154
GE Arize Element Top Light Mounting Installation Manual preview
Arize Element Top Light
Brand: GE Pages: 2
Datex-Ohmeda Aestiva/5 Operation Manual preview
Aestiva/5
Brand: Datex-Ohmeda Pages: 104
Baker Hughes Druck DPI 620 Genii Instruction Manual preview
Druck DPI 620 Genii
Brand: Baker Hughes Pages: 166
Baker Hughes Druck DPI 620 Genii Safety And Quick Start Manual preview
Druck DPI 620 Genii
Brand: Baker Hughes Pages: 340
YSI 5000 Operation Manual preview
5000
Brand: YSI Pages: 70
jcb CT160 Service Manual preview
CT160
Brand: jcb Pages: 41
Obdstar BT06 Instructions For Functions preview
BT06
Brand: Obdstar Pages: 10
UFO Vega Product User Manual preview
Vega
Brand: UFO Pages: 16
Tascam DP-02 Owner'S Manual preview
DP-02
Brand: Tascam Pages: 80
Tascam DP-01 Specifications preview
DP-01
Brand: Tascam Pages: 2
Walker A10 Operator'S Manual preview
A10
Brand: Walker Pages: 24
BACtrack ELEMENT Product Manual preview
ELEMENT
Brand: BACtrack Pages: 16
Qlight S80S Manual preview
S80S
Brand: Qlight Pages: 3
qtran Q-VAULT-5 Installation preview
Q-VAULT-5
Brand: qtran Pages: 2
Q-Optics Radiant Instructions & Care preview
Radiant
Brand: Q-Optics Pages: 2

Brands by name

Popular brands

Load more brands