Covidien Puritan Bennett 700 Series Service Manual Download Page 215

Page: 215 / 439

Diagnostic codes

Puritan Bennett™ 700 Series Ventilator System Service Manual

10070389 Rev. A

6-9

6028

BIOT (technical alert --
CONTACT SERVICE)

Safety valve should be closed,
but measured current is too
high

1. Check that safety valve/ventilator head

harness connection is secure.

2. Check safety valve resistance (10.5 to

3. Replace safety valve.
4. Replace pressure solenoid PCB.

6029

BIOT (technical alert --
CONTACT SERVICE)

No current to ALARM light
when it should be on

1. Replace UI display PCB.
2. Replace controller PCB.

6030

BIOT (technical alert --
CONTACT SERVICE)

There is current to ALARM
light when it should be off

1. Replace UI display PCB.
2. Replace controller PCB.

6031

BIOT (technical alert --
CONTACT SERVICE)

No current to CAUTION light
when it should be on

1. Replace UI display PCB.
2. Replace controller PCB.

6032

BIOT (technical alert --
CONTACT SERVICE)

There is current to CAUTION
light when it should be off

1. Replace UI display PCB.
2. Replace controller PCB.

6033

BIOT (technical alert --
CONTACT SERVICE)

Battery current low

1. Replace appropriate battery.
2. Replace BBU PCB.
3. Replace controller PCB.

6034

BIOT (technical alert --
CONTACT SERVICE)

Battery current high

1. Replace appropriate battery.
2. Replace BBU PCB.
3. Replace controller PCB.

6035

BIOT (technical alert --
CONTACT SERVICE)

PEEP pump current low

1. Verify resistance of PEEP pump is

between 12 and 15

measured when

pump is at ambient temperature. If it is
not replace pump.

2. Check continuity of wiring to PEEP

pump. Replace harness if necessary.

3. Replace pressure solenoid PCB.
4. Replace BBU PCB.
5. Replace controller PCB.

6036

BIOT (technical alert --
CONTACT SERVICE)

PEEP pump current high

1. Verify resistance of PEEP pump is

between 12 and 15

measured when

pump is at ambient temperature. If it is
not replace pump.

2. Check continuity of wiring to PEEP

pump. Replace harness if necessary.

3. Replace pressure solenoid PCB.
4. Replace BBU PCB.
5. Replace controller PCB.

6037

BIOT (technical alert --
AIR INTAKE ABSENT)

Air intake filter switch open

1. Verify air intake filter is installed and

that it engages air intake filter switch.

2. Check that air intake filter switch/

ventilator head harness connection is
secure.

3. Replace air intake filter.
4. Replace air intake filter switch.
5. Replace pressure solenoid PCB.

6038

BIOT (technical alert --
CONTACT SERVICE)

NVRAM failure

1. Replace NVRAM.
2. Replace controller PCB.

Table 6-1: Diagnostic codes (continued)

Code

Software

Possible cause

Corrective action

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Search results

Summary of Contents for Puritan Bennett 700 Series

Reviews:

Related manuals for Puritan Bennett 700 Series

Brands by name

Popular brands

Covidien Puritan Bennett 700 Series, Service Manual

Search results

Summary of Contents for Puritan Bennett 700 Series

Reviews:

Related manuals for Puritan Bennett 700 Series

Brands by name

Popular brands