manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Service Manual

The Covidien Puritan Bennett 700 Series service manual is essential for maintaining and troubleshooting your medical equipment. Download the manual for free from manualshive.com to ensure optimal performance and reliable operation of your device. Get the detailed instructions you need to properly service your Puritan Bennett 700 Series product.

Share
Download
background image

Alphabetic part index

A-12

10070389 Rev. A

Puritan Bennett™ 700 Series Ventilator System Service Manual

Spacer, nylon, UI encoder (Attaches rotary encoder)

G-060906-00

Figure 9-7

16

Speaker

G-060496-00

Figure 9-14

9

Standoff, M3 (attaches pressure solenoid PCB)

G-061677-00

Figure 9-14

20

Standoff, male-female, M3 x 6 (Separates BBU PCB from 
power tray)

G-060535-00

Figure 9-20

34

Standoff, male-female, M3 x 17 (Attaches pressure solenoid 
PCB)

G-061410-00

Figure 9-14

19

Standoff, male-male, M3 x 10 (Attaches controller PCB)

G-060505-00

Figure 9-14

18

Static dissipative field service Kit

G-06166-00 

Table 5-2

N/A

Section 8.1.7.2

N/A

Strip, thermal conductive

G-060937-00

Figure 9-20

49

Support, oxygen cylinder (lower)

--

Figure 9-5

9

Support bracket, Fisher & Paykel™* humidifiers

--

Figure 9-5

32

Figure 9-6

21

Switch, air intake filter

G-061572-00

Figure 9-8

51

Switch, power

G-060031-00

Figure 9-20

7

Tape, PTFE (Used on threads of oxygen adapters)

Figure 9-9

10

Tape, PTFE (Used on threads of oxygen fitting)

Figure 9-8

44

Tape, PTFE (Used on threads of oxygen fitting, oxygen 
regulator pressure transducer, and oxygen regulator 
extension)

Figure 9-12

9

Thermistor, inspiration manifold

G-060095-00

Figure 9-11

7

Thermistor assembly, air flow

G-060845-00

Figure 9-8

32

Thermistor assembly, exhalation

G-060844-00

Figure 9-13

15

Tie wrap, air intake (Attaches BBU PCB/ventilator head 
harness to upper righthand screw at rear of air intake 
housing)

G-061088-00

Figure 9-8

50

Transducer, pressure, oxygen regulator

G-061694-00

Figure 9-12

8

Tube, adult, 15-cm (Connects collector vial to expiratory 
filter)

G-061441-00

Figure 9-1

7

Tube, silicone, 1/8-in. ID x 1/4-in. OD

--

Figure 9-23

18

Figure 9-23

19

Figure 9-23

20

Tube, silicone, 3-mm ID x 6-mm OD

--

Figure 9-23

2

Figure 9-23

3

Figure 9-23

4

Figure 9-23

5

Tube, silicone, 3-mm ID x 6-mm OD, 16.0-cm

--

Figure 9-17

6

Tube, silicone, 3/16-in. ID x 3/8-in. OD

--

Figure 9-17

8

Figure 9-23

7

Figure 9-23

8

Figure 9-23

9

Figure 9-23

10

Tube, silicone, 3/16-in. ID x 3/8-in. OD, 13.0-cm

--

Figure 9-17

7

Description

Part no.

Figure no.

Item no.

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Puritan Bennett 700 Series

3M Littmann 3200 User Manual preview
Littmann 3200
Brand: 3M Pages: 48
3M Littmann 3100 Instructions For Use Manual preview
Littmann 3100
Brand: 3M Pages: 19
3M Speedglas G5-01 User Instructions preview
Speedglas G5-01
Brand: 3M Pages: 62
Thomas & Betts Quickfit Nexus Exit Installation Manual preview
Quickfit Nexus Exit
Brand: Thomas & Betts Pages: 2
idiag P100 Manual preview
P100
Brand: idiag Pages: 10
Bandit 2290 Operating & Parts Manual preview
2290
Brand: Bandit Pages: 136
3M Versaflo S Series User Instructions preview
Versaflo S Series
Brand: 3M Pages: 11
3M DBI Sala EXOFIT User Instructions preview
DBI Sala EXOFIT
Brand: 3M Pages: 32
3M 746 Instructions Manual preview
746
Brand: 3M Pages: 8
Accurate Bio-Medical Technology WS Series User Manual preview
WS Series
Brand: Accurate Bio-Medical Technology Pages: 35
JB-Lighting P4 Operating Instructions Manual preview
P4
Brand: JB-Lighting Pages: 60
BARKO LOADERS 295 Service Manual preview
295
Brand: BARKO LOADERS Pages: 85
Idmed ToFscan Quick Start preview
ToFscan
Brand: Idmed Pages: 2
unios Echo Quick Installation Manual preview
Echo
Brand: unios Pages: 2
laerdal MegaCode Kelly Manual preview
MegaCode Kelly
Brand: laerdal Pages: 8
LAHTI PRO 46018 User Manual preview
46018
Brand: LAHTI PRO Pages: 16
laerdal LSU Directions For Use Manual preview
LSU
Brand: laerdal Pages: 32
laerdal Resusci Anne Important Product Information preview
Resusci Anne
Brand: laerdal Pages: 32

Brands by name

Popular brands

Load more brands