manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Service Manual

The Covidien Puritan Bennett 700 Series service manual is essential for maintaining and troubleshooting your medical equipment. Download the manual for free from manualshive.com to ensure optimal performance and reliable operation of your device. Get the detailed instructions you need to properly service your Puritan Bennett 700 Series product.

Share
Download
background image

Parts list

Puritan Bennett™ 700 Series Ventilator System Service Manual

10070389 Rev. A

9-27

9.10  Oxygen hose adapters 

Figure 9-9. Oxygen hose adapters

Oxygen hose adapters parts list

Item no. 

(Figure 9-9)

Part no.

Quantity

Description

1

G-061267-00

1

Adapter, oxygen hose, DISS male to DISS male (for Canada)

2

G-061192-00

1

Adapter, oxygen hose, DISS male to Air Liquide™* (for France) 

3

G-061193-00

1

Connector with O-ring, oxygen hose, Air Liquide™* (for France)

4

G-061194-00

1

•

O-ring, oxygen hose, Air Liquide™* (for France)

5

--

1

•

Connector, oxygen hose, Air Liquide™* (for France)

6

G-061177-00

1

Adapter, oxygen hose, DISS male to 1/4 NPT (for United Kingdom/
Australia)

7

G-061199-00

1

Connector, oxygen hose, 1/4 NPT to NIST (for United Kingdom)

8

G-061195-00

1

Adapter, oxygen hose, 1/4 NPT to Australian type (not shown)

9

G-061196-00

1

Collar, oxygen hose, Australian type (not shown)

10

G-060759-00

As needed

Tape, PTFE (Used on threads of oxygen adapters as shown. For 
Australian type adapter assembly, used on threads of DISS fitting 
and 1/4 NPT adapter.)

11

G-062194-00

1

Hose assembly, connector, Swiss (not shown)

1

10

7-00189

DISS 
male 
oxygen 
hose

Male 
DISS 
fitting

2

4

5

3

10

7-00190

Air 
Liquide™* 
oxygen 
hose

Male 
DISS 
fitting

6

7

10

10

7-00191

Male 
DISS 
fitting

NIST 
oxygen 
hose

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Puritan Bennett 700 Series

ACS 3200 Series Operation And Instruction Manual preview
3200 Series
Brand: ACS Pages: 56
Bartscher 700 Series Instructions For Installation, Use And Maintenance Manual preview
700 Series
Brand: Bartscher Pages: 22
Raymarine ST7000 Installation Instructions Manual preview
ST7000
Brand: Raymarine Pages: 55
Halyard MIC Series Instructions For Use preview
MIC Series
Brand: Halyard Pages: 4
GAME Underwater Light Show & Fountain Instructions preview
Underwater Light Show & Fountain
Brand: GAME Pages: 2
Landoll 7812 Operator And Parts Manual preview
7812
Brand: Landoll Pages: 52
Gason 7390 Operator'S Manual preview
7390
Brand: Gason Pages: 110
Panasonic LP-M Series Maintenance Manual preview
LP-M Series
Brand: Panasonic Pages: 174
ACCU-CHECK AVIVA COMBO Reference Manual preview
AVIVA COMBO
Brand: ACCU-CHECK Pages: 104
Gebhardt Anlagentechnik EHA40 Translation Of The Original Operating Manual preview
EHA40
Brand: Gebhardt Anlagentechnik Pages: 152
Hach 2100N Basic User Manual preview
2100N
Brand: Hach Pages: 58
Hach 2100AN IS User Manual preview
2100AN IS
Brand: Hach Pages: 52
Ognibene STA Service Manual preview
STA
Brand: Ognibene Pages: 28
Hameg HM303-6 Manual preview
HM303-6
Brand: Hameg Pages: 24
Vaisala HMP Series User Manual preview
HMP Series
Brand: Vaisala Pages: 118
laerdal SimPad Quick Start Manual preview
SimPad
Brand: laerdal Pages: 9
Martin Maxedia 4 User Manual preview
Maxedia 4
Brand: Martin Pages: 202
WE-EF VLR100 LED Series Installation And Maintenance Instructions preview
VLR100 LED Series
Brand: WE-EF Pages: 3

Brands by name

Popular brands

Load more brands