manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Service Manual

The Covidien Puritan Bennett 700 Series service manual is essential for maintaining and troubleshooting your medical equipment. Download the manual for free from manualshive.com to ensure optimal performance and reliable operation of your device. Get the detailed instructions you need to properly service your Puritan Bennett 700 Series product.

Share
Download
background image

Alphabetic part index

A-8

10070389 Rev. A

Puritan Bennett™ 700 Series Ventilator System Service Manual

Nut, HEX (Attaches rotary encoder)

--

Figure 9-7

14

Nut, HEX, M2.5 (Attaches LCD panel)

G-060988-00

Figure 9-7

23

Nut, HEX, M3 (Attaches BBU PCB)

G-060989-00

Figure 9-20

30

Nut, HEX, M4 (Attaches bottom of cable management bar)

G-060990-00

Figure 9-14

2

Nut, HEX, M4 (Attaches keyboard to PCB)

Figure 9-7

7

Nut, HEX, M4 (Attaches line filter ground wire)

Figure 9-20

40

Nut, HEX, M4 (Attaches PEEP pump)

Figure 9-17

2

Nut, HEX, M4 (Attaches power input terminal ground wire)

Figure 9-20

54

Nut, HEX, M5 (Attaches ground wire)

G-060991-00

Figure 9-4

4

Nut, HEX, M5 (Attaches Hudson support bracket to cart 
interface bracket)

Figure 9-5

42

Nut, HEX, M6 (Attaches assembled ventilator/mount to 
shelf)

--

Figure 9-6

16

Nut, HEX, with washer, EX LK, M3 (Attaches expiratory filter 
housing to cabinet)

G-061055-00

Figure 9-13

20

Nut, HEX, with washer, EX LK, M3 (Attaches tension clip)

Figure 9-7

5

Nut, HEX, with washer, EX LK, M3 (Attaches UI to lid)

Figure 9-7

11

Nut, HEX, with washer, EX LK, M4 (Attaches cylinder cover 
or cylinder support to cart)

--

Figure 9-5

7

Nut, HEX, with washer, EX LK, M6 (Attaches cylinder 
bracket to cart)

--

Figure 9-5

15

NVRAM (nonvolatile RAM) (U6)

G-061686-00

Figure 9-14

15

O-ring, exhalation valve

G-060823-00

Figure 9-13

3

O-ring, oxygen hose, Air Liquide™* (for France)

--

Figure 9-9

4

Optoswitch (motor-opto) assembly

G-061255-00

Figure 9-18

16

Section 9.17

9

Oxygen regulator assembly

--

Figure 9-8

36

Oxygen regulator pressure transducer (P

O

) calibration tool

G-061541-00

Section 4.2.3.2.2

--

Oxygen sensor (includes oxygen sensor only)

4-072214-00

Figure 9-11

2

Oxygen sensor kit (includes oxygen sensor, sensor harness, 
adapter, and hardware; replaces sensor with integral 
harness)

G-062009-00

Figure 9-11

2

Section 9.25

3

Oxygen solenoid assembly

G-062023-00

Figure 9-12

3

Section 9.13

3

PCB, battery backup (BBU)

G-061129-00

Figure 9-20

25

PCB, controller

G-062146-00

Figure 9-14

14

Section 9.27

1

PCB, pressure solenoid

G-061127-00

Figure 9-14

16

PCB, 740 UI display

G-061130-00

Figure 9-7

6

PCB, 760 UI display

G-062227-00

Figure 9-7

6

PEEP pump and reservoir

--

Figure 9-8

39

Piston/cylinder assembly

G-061134-00

Figure 9-18

1

Plate, battery compartment access

G-060448-00

Figure 9-8

5

Figure 9-19

15

Plate, inspiratory access panel, Dutch

G-062312-00

Figure 9-8

4

Plate, inspiratory access panel, English

G-062303-00

Figure 9-8

4

Plate, inspiratory access panel, French

G-062304-00

Figure 9-8

4

Plate, inspiratory access panel, German

G-062305-00

Figure 9-8

4

Plate, inspiratory access panel, Italian

G-062306-00

Figure 9-8

4

Description

Part no.

Figure no.

Item no.

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Puritan Bennett 700 Series

Parker 6513 Technical Manual preview
6513
Brand: Parker Pages: 54
Nemco 9101 Installation And Operating Instructions Manual preview
9101
Brand: Nemco Pages: 13
Ecco 7950 Installation And Operation Instruction Manual preview
7950
Brand: Ecco Pages: 12
UMF Medical 5005 Service Manual preview
5005
Brand: UMF Medical Pages: 12
Obdstar MS50 User Manual preview
MS50
Brand: Obdstar Pages: 42
Yamaha QX1 Owner'S Manual preview
QX1
Brand: Yamaha Pages: 46
GE PWS Operating And Maintenance Instructions Manual preview
PWS
Brand: GE Pages: 18
Barreto HT712 Operator'S Manual preview
HT712
Brand: Barreto Pages: 16
Zimmer GED5000IL Series Installation And Operating Instructions Manual preview
GED5000IL Series
Brand: Zimmer Pages: 52
ALL-FILL VF100e Installation & Maintenance Manual preview
VF100e
Brand: ALL-FILL Pages: 32
Blatchford ESK+ Manual Knee Lock Instructions For Use Manual preview
ESK+ Manual Knee Lock
Brand: Blatchford Pages: 172
HEINE OPTOTECHNIK iC2 Funduscope Manual preview
iC2 Funduscope
Brand: HEINE OPTOTECHNIK Pages: 52
Ugin ARTIS NEO Instructions For Use Manual preview
ARTIS NEO
Brand: Ugin Pages: 39
Hubbell Dual-Lite EVHC-BC Series Installation, Operation And Service Instructions preview
Dual-Lite EVHC-BC Series
Brand: Hubbell Pages: 2
Nexen AIR CHAMP BD Caliper Brake User Manual preview
AIR CHAMP BD Caliper Brake
Brand: Nexen Pages: 16
Metrohm 776 Dosimat Instructions For Use Manual preview
776 Dosimat
Brand: Metrohm Pages: 42
Maquet Betastar 1131 Maintenance & Repair Instructions preview
Betastar 1131
Brand: Maquet Pages: 232
Master V- 550 Owner'S Manual preview
V- 550
Brand: Master Pages: 80

Brands by name

Popular brands

Load more brands