Chevrolet 10 Series 1970, Service Manual

Page: 80 / 671

BODY IB-2
F ig . 1 —C o n v e n tio n a l C ab and C om ponents
1. H eater H o le C o v e r A ssem bly
2. H ole Tapping - Dash and Toe
3. Side C o w l V e n tila t o r 'C a b and W /S C ow l
4. W /S W ip e r M o to r
5. W /S W asher Jar and Hoses
6. W /S W ip e r L inka ge
7 . W /S W ip e r Blades
8. Pad Assem bly and D e fro ste r O u t le t 15.
9. Ash Tray Assem bly and C o ve r C ab and W /S C o w l 16.
10. Instrum ent Panel C om partm ent 17.
11. Instrum ent Panel C om partm ent D oor 18.
12. W /S and Back W in d o w In s ta lla tio n 19.
13. Transmission C o ve r 20.
14. Dash M ats and F lo o r Insulators 21.
Dome Lamp A ssem bly
D oor Si 11 P late
Sunshade and Inside M ir r o r
Short and Long Arm M irr o r
Seat B elt In s ta lla tio n
Fuel C a u tio n P late
Body M o u n tin g
A ll openings that allow dust leaks w ill also p rovid e
w ater leaks. When checking fo r w ater leaks a helper
should be used on the inside of the cab or body to locate
the entrance of w ater, w hile it is applied on the outside.
NOTE: W a ter does not always enter the cab
o r body in the location w here leaks show up,
F ig . 2 — Body M o u n tin g N o . 1
th erefo re, back-trackin g the path of w ater w ill
show the true entrance of the leak.
FRONT END
WINDSHIELD GLASS
The windshield is a on e-p iece type and is retained in
the w indshield opening by a moulded rubber w eather­
strip .
Th is w eath erstrip is sealed in the windshield
opening and sealed to the w indshield glass.
When rep lacin g a cracked w indshield glass, it is v e ry
im portant that the cause of the glass breakage to d e te r­
mined and the condition c o rre c te d b e fo re a new glass is
installed. O therw ise, it is highly p ossib le that a sm all
obstruction o r high spot som ew here around the wind­
shield opening w ill continue to crack o r break the newly
in stalled windshield esp ecia lly when the strain on the
gla ss caused by this obstruction is in creased by such
conditions as wind p ressu res, ex trem es of tem perature,
m otion of the veh icle, etc.
The procedu re fo r rem o va l of the windshield applies
to the com plete windshield assem bly.
Removal
1. B efo re rem ovin g the windshield, m ark the location
of the break on the windshield rubber channel and
the body. P ro te c t the paint fin ish inside of the cab.
Mask around the windshield opening and outside,
lay a suitable coverin g a cro ss the hood and fenders.
NOTE: The windshield glass rubber w eather­
strip is one p iece. The glass is held in a chan­
nel within the w eath erstrip (fig . 8).
2. Do not tr y to rem ove re v e a l mouldings while wind­
sh ield is in body opening. R em ove fro m custom
CHEVROLET TRUCK SERVICE MANUAL