Chevrolet 10 Series 1970, Service Manual

Page: 340 / 671

ENGINE 6-18
and in sta ll o il sea l in the lo w er g roove o f the stem ,
making sure the sea l is fla t and not twisted.
NOTE: A light coat of o il on the sea l w ill help
prevent twisting.
7. Install the v a lv e locks and re le a s e the com p resso r
tool, making sure the locks seat p ro p e rly in the
upper gro o ve of the v a lv e stem .
NOTE: G rease may be used to hold the locks
in place w hile re le a s in g the co m p resso r tool.
8. Install spark plug, using a new gasket on 13/16"
plugs, and torque to sp ecification s.
9. Install and adjust v a lv e m echanism as outlined.
C ylinder Head Assemblies
Removal
1. Rem ove m anifold assem bly as outlined.
2. R em ove va lv e m echanism as outlined.
F ig . 4 L —O i l Pan G a s k e t and Seal L o c a tio n
3. Drain cooling system (block).
4. Rem ove fu el and vacuum line fro m retaining clip
at w ater outlet then disconnect w ire s fro m tem p era­
ture sending units.
5. Disconnect upper rad iator hose at w ater outlet hous­
ing and battery ground strap at cylin d er head.
6. R em ove coil.
7. R em ove cylin d er head bolts, cylin d er head and gas­
ket. P la ce cylin d er head on two blocks of wood to
preven t damage.
Installation
CA UTIO N: The gasket su rfaces on both the
head and the block must be clean of any fo reig n
m atter and fr e e o f nicks o r heavy scratches.
C ylin der bolt threads in the block and threads on
the cylin d er head bolt must be cleaned. (D irt
w ill affect bolt torque). Do Not use gasket s e a le r
on com position ste e l asbestos gaskets.
1. P la c e the gasket in position o v e r the dowel pins with
the bead up.
2. C arefu lly guide cylin d er head into p lace o v e r dowel
pins and gasket.
3. Coat threads of cylin d er head bolts with sealin g
compound and in sta ll fin g e r tight.
4. Tighten cylin d er head bolts a little at a tim e in the
sequence shown on the torque sequence chart until
the s p ecified torque is reached.
5. Install coil.
6. Connect upper rad iator hose and engine ground strap.
7. Connect tem peratu re sending unit w ire s and in stall
fu el and vacuum lin es in clip at w ater outlet.
8. F ill cooling system .
9. Install m anifold assem bly as outlined.
10. Install and adjust va lve mechanism as outlined.
11. In stall and torque ro c k e r arm co ver.
O il Pan
Removal
1. Disconnect battery ground cable then rem ove sta rter.
2. On CS 10-20-30.
a. R em ove engine fron t mount bolts (fra m e bracket-
to-m ount).
b. Using a suitable jack with a fla t piece of wood
(to preven t damaging o il pan), ra is e engine enough
to in sert 2” x 4" wood blocks between the engine
mounts and fra m e brackets.
3. Drain engine oil.
4. Rem ove o il pan and discard gaskets and seals.
Installation
1. Thoroughly clean a ll gasket sealing surfaces-
2. Install new re a r seal in re a r main bearing cap.
3. Install new front seal on crankcase front co v e r
p ressin g tips into holes provided in c o ver.
4. Install new side gaskets on cylin d er block (fig. 4 L).
NOTE : DO NOT USE S E A LE R .
5. Install o il pan and torque bolts to specification s.
6. Com plete installation as follow s on CS 10-20-30:
a. Using a suitable jack with a flat piece o f wood
(to preven t damaging o il pan), ra is e engine
enough to rem ove 2" x 4 " wood blocks from
between the engine mounts and fra m e brackets.
b. L o w er engine, install front mount bolts and torque
to specification s.
CHEVROLET TRUCK SERVICE MANUAL