manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 142

Print side 1

Print side 2

Strip

Function

Length of the strip

1

Leading strip

1600 mm (63 inch)

2

Lead-in image

250 mm (9.84 inch)

3

Lead-out image

250 mm (9.84 inch)

4

Trailing strip with a cutting line

1600 mm (63 inch)

5

Leading strip

1600 mm (63 inch)

6

Lead-in image

250 mm (9.84 inch)

Be aware you have to rotate the job for the inside 180 degrees.

The lead-in and lead-out images are used by the AAC to measure and correct for additional media
step errors caused by the ink layer of side 1, while printing side 2.

Procedure

1.

Load a media roll on position 2 in the media drawer, with the flap pointing towards you.

2.

Pull the media towards you.

3.

Uncurl the media using an empty roll.

4.

Turn the media back onto the roll in the drawer.

5.

Load the media in the inside printing manner, see 

Load weak media for inside printing on

page 108

.

6.

Place a new empty take-up roll core and push the media shaft back on the winder.

Print double-sided with manual cut

142

Chapter 4 - Handle the media

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands