manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 286

7.

Click on [req.csr] to download the file and save it.

8.

Create a backup to save the private key generated during the certificate request. For more
information, see 

Make a backup on page 295

.

9.

Use the certificate request file to get a valid certificate.

NOTE

Get a valid certificate from a Certification Authority (e.g. Thawte, Symantec, Comodo
etc.) or ask your IT administrator to get one from your company.

10.

Click on [Configuration] 

→

[Security].

11.

Click on [Upload].
A new window opens.

12.

Click on [Browse...] and select the valid certificate file.

13.

Click on [Upload].
A new window opens.

14.

Click on [Ok] to restart the system.
A 'failed' or 'success' window appears.

15.

Restart the printer. For more information, see 

Restart the printer on page 325

.

It is advised to make a new backup, which includes the complete valid certificate with the private
key.

Result

You can now use a browser and access the settings editor via HTTPS: https://<hostname>. Where
hostname is the common name or one of the three alternative names filled in.

You can find the protocol (HTTPS only/ HTTP or HTTPS) used for access to the settings editor
under [Configuration] 

→

[Security]. Note that WebDAV is not used for the Colorado 1630.

Enable the use of HTTPS

286

Chapter 8 - Configure the network and security settings

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands