manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 289

Change the HTTPS security settings

Introduction

You can change the default HTTPS security settings to best fit your configuration.

Illustration

Procedure

1.

Open the settings editor.

2.

Click on [Configuration] 

→

[Security].

3.

Click on [Edit] in the [HTTP/HTTPS] header.

4.

The [Use of less strong cipher suites] setting is by default disabled to secure data communication,
which is suitable for recent browsers. If you want to use older browsers or HTTPS clients, you can
change the setting to [Enabled].

5.

The [Minimal version of TLS protocol] setting is by default set to [TLSv1.2]. [TLSv1.2] is a
stronger protocol and [TLSv1.0] is weaker. You can change the setting to the minimum security
protocol that fits your security requirements. It is also possible to use a lower protocol to allow
communication with older browsers or HTTPS clients.

6.

Click on [OK] to save the settings.

Change the HTTPS security settings

Chapter 8 - Configure the network and security settings

289

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands