manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 368

4.

Go to the media output side and locate the guide plate with the roller assy and foams.

5.

Locate the roller assy under the guide plate.

6.

Pull to take out the roller.

7.

Locate the foam left of the roller assy. A pin is placed at the left end of the foam.

8.

Pull the pin and plug out with your fingers.

9.

Locate the foam right of the roller assy. A pin is placed at the right end of the foam.

10.

Pull the pin and plug out with your fingers.

11.

Slide both foams towards the middle to remove them.

12.

Dispose the roller assy, foams, pins and plugs as chemical waste according to local regulations.

13.

Take a lint free cloth and clean any residue ink left on the guide plate.
If necessary, dampen the cloth with the cleaning liquid to remove any remaining ink.

Clean the guide plate and replace the foams and roller assy

368

Chapter 9 - Troubleshooting and support

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands