manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 121

NOTE

In order to prevent winding issues when winding the media in the opposite direction of
the roll in the drawer, the media has to be taped with enough tapes over the full width
of the roll to straighten the curling edge.

9.

Move the media guides towards the middle to align with the media.

10.

On the operator panel tap on [Ready].
The printer continues printing while winding the job.

After you finish

When you want to stop winding you have to cut the media. For more information, see 

Cut the

media on page 145

, 

Cut the media (manual) on page 147

.

Print and wind without a tension bar

Chapter 4 - Handle the media

121

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands