manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 154

Unload a media roll from the drawer

Introduction

Unload a media roll from the drawer when you want to load a new media roll.

CAUTION

• Watch your fingers when you handle the media roll.
• Lifting heavy media, 25 kg (55 lb) or more, has to be done by at least two people or with the

help of external lifting tools.

IMPORTANT

• Handle the media roll with care. A dented media roll can damage the printer.
• Only open the media drawer when the indicator light on the drawer is on. Do not open the

drawer when the light is off, you can damage the machine.

NOTE

Put on gloves to avoid pollution of the paper by your fingerprints.

Procedure

1.

Pull firmly to open the media drawer.

2.

Use both hands to turn the media roll backwards (1) and remove the media from the metal paper
guide.

Unload a media roll from the drawer

154

Chapter 4 - Handle the media

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands