Canon Colorado 1630 Operation Manual Download Page 23 | Manualshive

Page: 23 / 388

Canon Colorado 1630 Operation Manual Download Page 23

cause pain and to take precautions to avoid unintentional contact with or exposure to those
energy sources.

Power source

WARNING

• Put the power plug directly into a power outlet that has the same configuration as the plug.

The use of an adapter can result in an inadequate power supply. If a proper power outlet is
not available, ask a qualified electrician to perform the installation.

• This machine has two power connections. Do not connect both mains power cables to same

building branch circuit.

IMPORTANT

• Do not connect the machine to a mains voltage or frequency which differs from the value

stated on the power marking label. When a connection to a different mains voltage or
frequency is required, contact your authorized service representative.

Grounding / Power cord

WARNING

• Do not scratch, abrade, heat, twist, bend, or place a heavy object on the power cord or cause

any other damage to it. The use of a damaged power cord (e.g. exposed core wire or broken
wire) could result in an electrical shock, fire or malfunction of the machine. If the power cord
is damaged, immediately switch off the power switch and unplug the power cord from the
power outlet. Contact your authorized service representative.

• Do not use a multiple outlet adapter or an extension lead. Contact your authorized service

representative if an extension lead is required. The use of an extension cord may result in fire
or electrical shock.

• Do not use any power cord other than the one provided. Never use the power cord with any

other electrical device.

• Only use a power cord that is fitted with a protective earth conductor.
• When the machine has to be connected via a wall socket, place the machine close to a wall

socket that is easily accessible. The power plug serves as a disconnecting device.

• Do not route the power cords in such a way that they can be stepped on or tripped over.
• Connect the power cord to a power outlet that is equipped with a protective earthing (PE)

terminal.

• This equipment is not designed for connection to an IT power system. An IT power system is

a voltage network in which the neutral wire is not connected to earth.

Safety and Environment Information

Chapter 2 - Safety information

23

«
...
21
22
23
24
25
...
»

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands