manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 228

Replace the rollers of the Xtran pinch

Introduction

You can replace the Xtran pinch rollers without service assistance. The total amount of rollers
over the full width of the printer is 32.

Video: 

 Replace the rollers of the Xtran pinch

.

The clamp and the roller with axis

Before you begin

Use Colorado 1630 prescribed:
• Microflex gloves for handling ink
• Xtran pinch rollers, axis and clamps
• Small screwdriver
• Piece of paper (A3)

NOTE

For information on the prescribed maintenance materials, see 

List of Colorado 1630

maintenance materials on page 255

.

CAUTION

Wear the prescribed gloves when contact with ink or maintenance materials is possible. Gloves
should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines carefully in
order to ensure maximum safety.

Replace the rollers of the Xtran pinch

228

Chapter 6 - Maintain the system

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands