manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 67

Change the media settings

Introduction

You can change the media settings of a media profile in the RIP.

When to do

Only when you create a new media profile or edit an existing media profile you can tune the
media settings. It is advised to use the Colorado 1630 media profiles and not change the media
settings. Only advanced users or application specialists should edit media profiles and have to
tune the media settings.

IMPORTANT

Changing the media settings can cause damage to your printer which may void your machine
warranty service.

NOTE

• Changing the media settings can result in poor print quality.
• This manual provides you with basic information in order to create and change media

profiles. Profiling is an expert task which requires additional information and tools not
covered by this manual. Contact your local support organization when you want to create or
change media profiles.

Before you begin

The location of the media settings differs, depending on the RIP you are using. For more
information, see 

Manage media profiles in ONYX on page 42

, 

Manage media profiles in Caldera

on page 53

.

Change the media settings

Chapter 4 - Handle the media

67

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands