manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 4

Source code

Introduction

The listed open source components are governed by different licenses. Some of the licenses
contain regulations regarding the provision of the pertaining source code.

Policy / Guidelines / Rules

If you would like to obtain a machine-readable copy of the source code of an open source
component, which is made available under applicable license terms, you may request such copy
of the source code by sending an e-mail to 

[email protected]

 indicating the following:

1. Name and version of the Canon Production Printing software you licensed.
2. Name and version of open source software modules contained in the above identified Canon

Production Printing software of which you legitimately would like to obtain the source code.

We will provide you with a find place where you can obtain a machine-readable copy of the
source code or we will deliver a complete machine-readable copy of the corresponding source
code of the respective open source software component, as available and as is, on a medium of
our choice which can be customarily used for software interchange. You may be required to pay
the cost incurred for the source code distribution, however, the cost will in no event excess the
cost incurred for physically performing the source code distribution.

Regulation notices

This offer is valid to anyone in receipt of this information.

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands