Canon Colorado 1630 Operation Manual Download Page 22 | Manualshive

Page: 22 / 388

Canon Colorado 1630 Operation Manual Download Page 22

The following labels are used to identify and categorize the hazard level:

Label

Type

Description

Warning

General warning sign.

Warning

Electricity: Hazardous electrical voltage inside. Do not remove
cover.

Caution

Hot surface: Take care to avoid direct contact with hot surfa-
ces.

Caution

Optical radiation: Take care to avoid injury to eyes and skin
when in the vicinity of optical radiation.

Caution

Sharp element: Take care to avoid injury from sharp ele-
ments.

Caution

Crushing of hands: Take care to avoid injury to hands when
in the vicinity of equipment with moving mechanical parts.

Label

Type

Description

Warning

Electricity: Warning, shock hazard. Dis-
connect all power plugs from their electri-
cal outlet before you start a maintenance
or repair action.

Warning

Electricity: Double-pole neutral fusing.
Risk of electric shock. Disconnect mains
before servicing.

Warning

Electricity: The machine must be connec-
ted to a grounded power outlet.

Caution

Electricity: High leakage current. The ma-
chine must always be connected to a
grounded power outlet.

Persons for ITE (LVD) machines according Directive 2014/35/EU

•

Instructed person

This User Documentation describes safeguards for the protection of an instructed person.
Instructed person is a term applied to persons who have been instructed and trained by a
skilled person, or who are supervised by a skilled person, to identify energy sources that may

Safety and Environment Information

22

Chapter 2 - Safety information

«
...
20
21
22
23
24
...
»

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands