manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 131

Print without winding

Introduction

You can also print without winding. Media that is printed without winding can be transported
well and is not too weak.

Before you begin

• Check the media category of your media. Media categories that need a tension bar cannot be

printed without winding.

• Printing without winding is set in the media type configuration in the RIP software. For printing

without winding you must select [no tension bar] under [Winding tension]. For more
information, see 

Change the media settings on page 67

.

• The printer is ready to print.

Procedure

1.

On the operator panel tap on the [Output] icon.

2.

Tap on [Output configuration].

3.

Make sure [Wind the output] is set to [No].

NOTE

Make sure you set the output configuration in time, as you cannot change the
configuration once the media has passed the clamp.

Print without winding

Chapter 4 - Handle the media

131

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands