manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 165

Use the PRISMAsync Remote Control app

Introduction

With the PRISMAsync Remote Control app you can monitor your Colorado 1630 at a distance.

Before you begin

To use the PRISMAsync Remote Control app you need a mobile device with:
• Google Android 8.0 or higher
• Apple iOS 12.5.5 or higher
• Remote connection on the printer must be enabled and working. For more information, see

Test PRISMAsync Remote Control on page 292

.

NOTE

You do not need a license for the PRISMAsync Remote Control app.
For more information, see the PRISMAsync Remote Control guide on the downloads website

http://downloads.cpp.canon

 under the product name.

Procedure

1.

Make sure the System administrator has added your email address as a PRISMAsync cloud
services user for the Colorado 1630. For more information, see 

Configure PRISMAsync Remote

Control on page 290

.

2.

Download the PRISMAsync Remote Control app via the Google Play Store or Apple App Store
onto your mobile device.

3.

Open the PRISMAsync Remote Control app on your mobile device.

4.

Log in with your Google or Microsoft account that has been registered by the System
administrator. The app opens and shows one or more printers you are connected to.

5.

Tap on the wheel icon on the bottom of the screen to configure the settings of the app.

6.

Use the app for:
•

Events

: see events and alerts, such as printing, roll empty, ink empty, all jobs finished,

maintenance tray full, replace filters, refill chiller, replace lubricators.

•

Printers

: monitor and view the status of one or multiple printers at one glance. Swipe to mute

the notifications.

•

Configuration

: configure the settings of the app.

Use the PRISMAsync Remote Control app

Chapter 5 - Print a job

165

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands