manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 10

About this guide 

Introduction

The guide addresses the Colorado 1630 and is written for the printer operator.

It describes 

the complete workflow of the printer

: from setup to the operation, maintenance and

troubleshooting of the machine.

Process

Actions

Reference

Before using the sys‐
tem

Components of the printer

Explore the system on page 31

Daily use

Use the RIP software

Configure media in the RIP on
page 42

Load, wind, and cut media

Handle the media on page 39

Print a job

Print a job on page 159

Improve quality

Improve quality on page 257

Maintenance

Maintain the print quality

Maintain the print quality on
page 168

Maintain the rest of the printer

Maintain the printer on page 196

Network and security

Network and security options

Configure the network and security
settings on page 267

Troubleshooting

Clear jams, stop the printer

General troubleshooting on
page 324

Clean polluted parts

Clean pollution on the printer on
page 364

Operator skill level

This guide describes safeguards for the protection of an instructed person. Instructed person is a
term applied to persons who have been instructed and trained by a skilled person, or who are
supervised by a skilled person, to identify energy sources that may cause pain and to take
precautions to avoid unintentional contact with or exposure to those energy sources.

About this guide

10

Chapter 1 - Introduction

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands