manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 168

Maintain the print quality

Guidelines to maintain the print quality

Introduction

To keep the printer in optimal condition it is very important to perform printhead and system
maintenance actions regularly. These maintenance actions can be performed at any time to solve
print quality problems, for example after a media crash.

You can start the maintenance actions from the operator panel. Depending on the situation there
are three different scenario's to choose from:
1. Manual maintenance
2. Automatic maintenance
3. Periodic maintenance

Depending on the chosen scenario a number of maintenance actions will be done automatically
by the printer and/or the operator.

For more details see video 

 Guidelines to maintain the print quality

Maintenance videos

The maintenance actions are explained in separate maintenance procedure videos.

Click on 

 Instruction videos

 or scan the following QR code to visit the instruction videos main

page.

Action

Procedure

Automatic nozzle optimization

Video: 

 Automatic nozzle optimization

Clean the nozzles

Video: 

 Clean the nozzles

Clean the maintenance station, wiper
and clean wall

Clean the maintenance station, wiper and clean wall on
page 178

Video: 

 Clean the maintenance station

Clean the matrix plate area

Clean the matrix plate area on page 182

Video: 

 Clean the matrix plate

Clean the mirrors

Clean the mirrors on page 247

4

Maintain the print quality

168

Chapter 6 - Maintain the system

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands