manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 178

Clean the maintenance station, wiper and clean wall

Introduction

The maintenance station plays an important role to keep the printheads optimally cleaned. In the
maintenance station you have to clean the wiper and the clean wall.

Video: 

 Clean the maintenance station

Before you begin

Use Colorado 1630 prescribed:
• Microflex gloves for handling ink
• Lint free cloths and swabs
• Cleaning liquid (Cleaner MB - Methyl benzoate)

NOTE

For information on the prescribed maintenance materials, see 

List of Colorado 1630

maintenance materials on page 255

.

CAUTION

• Wear the prescribed gloves when contact with ink or maintenance materials is possible.

Gloves should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines
carefully in order to ensure maximum safety.

IMPORTANT

Use the prescribed cleaning liquid. Do not use any other cleaners.

Procedure

1.

Start the maintenance action via the operator panel. For more information, see 

Start manual

maintenance on page 174

.

2.

Put on the Colorado 1630 approved gloves.

3.

Open the top cover from the media input side.

4.

Locate the maintenance station with the wiper and the clean wall on the right hand side.

Clean the maintenance station, wiper and clean wall

178

Chapter 6 - Maintain the system

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands