Canon Colorado 1630 Operation Manual Download Page 332

Page: 332 / 388

Turn the printer on after a power cut

Introduction

When power has been cut to the machine, you have to power the machine on. The machine has
to be on to keep the printer in optimal condition.

NOTE

There are 2 types of the cover under the roll winder. In the new design you can access the power

switch through an opening in the cover.

First design

New design

Procedure

Move to the media output side.

Pull to open the cover under the roll winder.

NOTE

For the new design, skip this step. You can access the power switch without opening
the cover.

Switch the power switch to the 'off' position.

Wait 1 minute.

Switch the power switch to the 'on' position.

Turn the printer on after a power cut

332

Chapter 9 - Troubleshooting and support

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Search results

Summary of Contents for Colorado 1630

Reviews:

Brands by name

Popular brands

Canon Colorado 1630, Operation Manual

Search results

Summary of Contents for Colorado 1630

Reviews:

Brands by name

Popular brands